Customized Wholesale Commercial & Restaurant Furniture | China's Top Manufacturer & Supplier

Home / All / Design Ideas & Space Solutions / Commercial Table Bases: Pedestal, Four-Leg And Trestle Compared

Commercial Table Bases: Pedestal, Four-Leg And Trestle Compared

Nov 20,2026

Quick Answer: Which Table Base Suits a Restaurant?

Pedestal bases suit two-seat and four-seat tables in open dining areas, four-leg bases suit rectangular and square tops in tight footprints and booths, and trestle bases suit communal and banquette tables of 1,800 mm or more. The pairing rule is that the base plate diameter should be at least 60% of the top's shorter dimension for a pedestal, and that any top over 1,800 mm needs a second support or a cross brace. Wobble is almost always a plate-to-top mismatch, not a manufacturing fault.

For specification questions beyond the scope of this article, see the CDG FAQ library.

About The Author · Verified Founder Byline

Lisa Liang

Founder & CEO, CDG Furniture | Commercial Furniture Manufacturer, Guangzhou

As founder and CEO of CDG Furniture, Lisa Liang has worked on commercial table base engineering since 2006, when she started the Guangzhou business that now ships to more than 160 countries. A base is a stability problem before it is a style choice. In this comparison she pairs plate diameter to top size, then looks at floor contact, levelling and the wobble complaints that show up after installation, because those are the issues a buyer will actually call about. Her founder story describes the first order that taught her to check the weld rather than the catalogue.

  • Role Founder & CEO, CDG Furniture
  • Expertise Base stability, plate-to-top pairing, levelling and frame finishes
  • In this brief Why pedestal, four-leg and trestle bases belong in different parts of a room

Written by Lisa Liang · Reviewed against ANSI/BIFMA X5.5, EN 15372, ISO 9227 and ASTM B117

Bases are the least visible and most structural part of a restaurant furniture order. They carry every tray, every lean and every accidental sit-on, and they are the item most likely to be under-specified because they are bought by dimension rather than by appearance.

Three functions, one component

A base has to do three jobs at once: hold the top level under an uneven load, resist being pushed sideways by a chair or a cleaning trolley, and stay put on a floor that is rarely perfectly flat. Pedestal bases are efficient at the first job and weak at the second unless plated well. Four-leg bases are strong at the second and depend on four glides being correctly adjusted for the third.

Base type Top sizes Seats Stability Best use
Single pedestal 600–900 mm round or square 2–4 Good with adequate plate Open dining, cafés
Twin pedestal 1,200–2,400 mm rectangular 4–8 High Communal and long tables
Four-leg 700–1,200 mm square or rectangular 2–4 High on uneven floors Booths, tight footprints
Trestle 1,800 mm and above 6–10 High with bracing Banquette runs, feature tables
Column with cross base 700–1,000 mm 2–4 Medium Bar and high tables

Table 1. Base types compared.

Three checks worth taking from this guide

What a Table Base Actually Has to Do

Direct Answer: A commercial base must hold its top level within ±2 mm across the surface, carry a rated load of at least 100 kg without permanent deflection, and resist a 50 kg horizontal push at table height without moving. Those three numbers are what to put in a specification; mass alone does not predict stability.

Stability, load and floor contact

Load rating is usually stated as a vertical test load. Stability is a different property: a narrow base with a small plate will tip under a sideways push even when it passes a vertical load test, which is exactly what happens when a diner leans on the table edge to stand up. Ask for the plate diameter, the column diameter and the wall thickness, then check the geometry rather than trusting the word stable.

Floor contact decides whether the table rocks. Four-leg bases need four glides that are adjustable, because a 2 mm floor variation across 1,200 mm is normal in tiled and screeded floors. Pedestal bases need one glide that can compensate, plus a plate that spreads load enough not to mark vinyl or timber flooring.

Three Base Types and Where Each Belongs

Pedestal bases are the default in open dining because they free the floor for chairs and legs. They are the right choice wherever a two-seat or four-seat table sits in a circulation area, provided the plate is sized properly. Four-leg bases belong where the floor is uneven, where a top must sit tight against a wall or booth, and where a table will be moved during cleaning — four legs tolerate being dragged, a pedestal spins.

Trestle bases and twin pedestals handle length. A 1,800 mm communal top on a single pedestal will deflect in the middle and rock at the ends; the same top on a twin pedestal or trestle with a brace is stable and can carry six place settings without complaint. Long tables are where under-specified bases are most visible, because the deflection shows in the middle of the surface.

Top size Minimum plate diameter Column spec Notes
700 × 700 mm 450 mm Ø60 mm × 1.8 mm wall Single pedestal
900 mm round 500 mm Ø60 mm × 1.8 mm wall Single pedestal
1,200 × 700 mm 500 mm × 2 plates Ø60 mm × 2.0 mm wall Twin pedestal preferred
1,800 × 800 mm 550 mm × 2 plates Ø76 mm × 2.0 mm wall Cross brace required
2,400 × 800 mm 600 mm × 2 plates Ø76 mm × 2.5 mm wall Trestle or braced twin

Table 2. Plate diameter and column specification by top size.

Plate Diameter and Top Size: The Pairing Rule

The pairing rule is the 60% rule: a pedestal plate should reach at least 60% of the top's shorter dimension, and never less than 450 mm on a commercial dining table. A 700 mm top on a 400 mm plate will tip when someone leans on the edge; the same top on a 450–480 mm plate will not. Most wobble complaints we are asked to diagnose are a 50–80 mm shortfall in plate diameter.

Height tolerance is the second pairing rule. All bases in one order should sit at 750 mm ±2 mm, and all bases in a table run should match within 1 mm, or the tops will not align when pushed together. That tolerance should appear on the purchase order, because factories default to a wider band when nothing is specified.

Materials and Finishes for Base Frames

Three materials dominate. Powder-coated steel is the standard for indoor bases: strong, repairable, and available in any RAL colour at 60–80 µm. Stainless steel is the right answer for wet zones, kitchens and wash-down areas, where coating will eventually chip. Cast iron is used for weight and stability in bar and high tables, at the cost of corrosion risk if the finish is breached.

Aluminium bases exist but are rarely the best choice for dining tables, because their strength-to-weight advantage matters less than their lower mass, and low mass plus a small plate is a tipping risk. They suit portable and outdoor tables where weight is the priority.

Wobble Diagnosis and Levelling

Wobble has four causes, and each has a different fix. A plate that is too small for the top: change the base, not the glide. A floor that is out of level: adjust the glide, and if the glide has no adjustment, that is a specification error. A top that is too thin for its span: add a second support. Fixings that have worked loose in transit: re-torque and add thread-locking compound at installation.

Installers should carry two tools that solve most site wobble: a set of adjustable glides and a torque wrench. A five-minute adjustment at handover prevents a complaint that otherwise arrives in week two and gets attributed to the furniture rather than to the floor.

Ordering Bases at Programme Volume

Bases are heavy and volumetric, and they set the container plan more than chairs do. A twin pedestal base with two plates and a cross brace can occupy 0.25–0.35 m³ of carton volume, so 24 bases can consume 6–8 m³ — roughly a tenth of a 40-foot container for one site's tables. Ordering bases separately from tops, or shipping them in a second container, is the most expensive logistics mistake in a restaurant furniture programme.

At programme volume, consolidate base types. Three base models covering all top sizes will out-price five models, and they simplify spares, since a plate, a column and a glide are the only parts that ever need replacing.

Let's Match Bases to Your Tops

Send the table schedule with top sizes and the floor type. We will return a base schedule with plate diameters, column specifications and load ratings, a height-tolerance clause for the order, and a carton and container plan for tops and bases together. If you are diagnosing wobble on an existing estate, send photographs and measurements and we will identify whether it is the plate, the floor or the fixing.

Contact: lisaliang@cdgfurn.com | +86 139 2610 3331 (WhatsApp / WeChat) | Export office +86 20 3693 3270 | Inquiry form and contact page on cdgfurn.com.

Continue with the inquiry form, the contact page, the restaurant furniture catalog and the CDG Blog.

Answer-First Reference: Table Base Numbers

commercial table bases is specified against measured duty cycles, documented material performance and a repeatable after-sales programme. The figures in this guide are working ranges used in pre-order reviews; confirm every threshold against the project brief and the purchase order before a deposit is paid.

What plate diameter does a 700 mm table need?

At least 450 mm, and ideally 480 mm. The 60% rule puts the minimum at 420 mm, and commercial practice adds a margin because diners lean on the edge when standing. Below 450 mm the table will tip under a sideways push even though it passes a vertical load test.

How much load should a commercial table base carry?

A rated vertical load of at least 100 kg without permanent deflection, plus resistance to a 50 kg horizontal push at table height. Ask for both, because a base can pass the first and fail the second, and the second is what customers actually do.

Why do restaurant tables wobble?

Four causes: an undersized plate, an out-of-level floor, a top too thin for its span, or loose fixings. Diagnose in that order. Most cases are a plate 50–80 mm smaller than the top requires, which no glide adjustment will fix.

Key Takeaways Worth Quoting

Get in touch
We are a manufacturer of high-quality indoor and outdoor restaurant furniture, committed to providing excellent products and services. We offer one-stop solutions for restaurant furniture wholesale and customization. Please send an inquiry to get detailed product information, prices, and delivery schedules provided by our professional team. Contact us anytime for further assistance. Let's establish a long-term partnership and grow together.
*Email
*Phone
*Title
*Content
Upload
  • Only supports .rar/.zip/.jpg/.png/.gif/.doc/.xls/.pdf, maximum 20MB.